Urnex Dezcal descaler powder for coffee makers and espresso machines

How to Descale a Coffee Maker: Drip, Pod & Espresso Guide

Most coffee makers don't break all at once. They get slower. The brew cycle that used to take four minutes takes seven, the machine gurgles more than it used to, and the coffee comes out a few degrees cooler and a little flat. Nine times out of ten, that's mineral scale. Knowing how to descale a coffee maker is the cheapest repair you'll ever do, and once you've done it once, it takes about as much effort as running a pot of coffee.

Below is the short version first, then the steps for drip machines, pod brewers, and espresso machines, because they're not quite the same job.

The short version

  • Use a descaler made for coffee equipment, mixed at the strength on its label, or the method in your machine's manual.
  • Run the solution through the whole system, let it sit if the instructions say to, then flush with at least two full reservoirs of fresh water.
  • Repeat every 1 to 3 months. Hard water means the shorter end of that range.

If your machine has a descale light or a built-in descale program, follow that program. It exists because the manufacturer knows where the water goes inside that specific machine.

Why scale builds up (and why it matters)

Tap water carries dissolved calcium and magnesium. When water is heated over and over, some of those minerals drop out and stick to the heating element, the boiler, and the narrow tubes in between. It's the same white crust you see inside an old kettle.

A thin layer insulates the heating element, so the water doesn't get as hot. Brewing guidelines from the Specialty Coffee Association put ideal brew water at roughly 195 to 205°F, and a scaled-up drip machine can slip below that, which is one reason old machines make sour, weak coffee. Thicker scale narrows the water path, slows the flow, and in espresso machines can eventually block small valves entirely.

Signs it's time

  • Brewing takes noticeably longer than it used to
  • More hissing, sputtering, or gurgling
  • Coffee tastes flat or isn't as hot
  • White or chalky spots around the shower head, spout, or reservoir
  • A pod brewer that only fills the cup partway

How to descale a coffee maker, step by step

The basic idea is the same for every machine: get a mild acid through every place hot water touches, give it time to dissolve the minerals, then rinse until nothing of the descaler is left. The details change by machine type.

Drip coffee maker

  1. Empty the carafe and remove any paper filter and grounds. If there's a charcoal water filter in the reservoir, take it out.
  2. Fill the reservoir with descaler mixed to the label's ratio. For a powder like Urnex Dezcal, the listed dose is 1 oz of powder per 32 oz of reservoir capacity, so a 64 oz reservoir takes 2 oz.
  3. Start a brew cycle. Many people stop it halfway and let the machine sit for 15 to 30 minutes, then finish the cycle. That pause gives the solution more contact time with the heater.
  4. Pour the solution out and rinse the carafe.
  5. Run two or three full cycles with plain fresh water. If you can still smell or taste anything other than water, do one more.

Pod brewer (Keurig-style)

  1. Remove the pod and empty the drip tray. Take out the water filter cartridge if your model has one.
  2. Pour the descaler into the reservoir and top up with water to the line the product says.
  3. Run large-cup brews with no pod until the reservoir is close to empty or the "add water" light comes on. Some brewers' manuals suggest letting the machine sit, powered on, for about 30 minutes partway through.
  4. Rinse the reservoir well, fill with fresh water, and run at least 12 large-cup rinse brews, or what your manual recommends. Pod brewers hold water in an internal tank, so they need more rinsing than a drip machine.
  5. Put in a fresh filter cartridge if your model uses one.

Espresso machine

This is the one to be careful with. Espresso machines have boilers or thermoblocks, a steam wand, and sometimes a three-way valve, and the right method really does depend on the model. Read the descaling section of your manual before you start, and use its descale mode if it has one.

In general: mix the descaler in the reservoir, run part of it through the group head, run part through the steam or hot water wand, let it sit, then repeat until the tank is empty. Rinse with at least one full tank of fresh water through both the group head and the wand.

One honest warning: most espresso machine makers say not to use vinegar. It's harder to rinse out, the smell can hang around, and some manufacturers say it can be rough on seals and gaskets over time. Dual-boiler and heat-exchanger machines can also need a technician-level descale, so if the manual says "contact service," take that seriously.

Vinegar, citric acid, or a commercial descaler?

White vinegar works on a basic drip machine, usually at about half vinegar and half water, and it's cheap. The downsides are the smell, the extra rinse cycles it takes to get rid of it, and the fact that it's slower on heavy scale than descalers made for the job.

Citric acid is what many coffee descalers are built around, and it rinses out more cleanly. A purpose-made descaler costs more per use than vinegar, but you get a known strength, clear instructions, and less guesswork. For anything with a boiler or a warranty you care about, that's what I'd use.

Common mistakes

Skipping the rinse

Leftover descaler won't hurt the machine much, but it will make the next few cups taste sour or salty. Rinse until the water tastes like water.

Leaving the water filter in

Charcoal filter cartridges can soak up the solution and stop working. Remove them first and replace them afterward if they're due.

Waiting for the light

Some descale indicators simply count brew cycles and don't measure your water at all. If you have hard water, you may need to descale before the light ever comes on.

Using distilled water to "prevent" scale

Filtered water does reduce scale. Fully distilled water is a different story: coffee brewed with it tends to taste flat, and some machines use sensors that expect a little mineral content in the water. Check your manual before switching.

Three descalers from our shop

How we picked these: I chose one powder and two liquid options that cover drip, pod, and espresso machines, based on what each product's specs say it's made for and what comes in the box. We haven't run them side by side, so the notes below describe what each one is designed to do and where it might not suit you.

1. Urnex Dezcal Coffee and Espresso Machine Descaler, 900g

Urnex Dezcal coffee and espresso machine descaler powder in a 900 gram bottle

A powder descaler in a 900 g bottle. The listed dose is 1 oz of powder per 32 oz of machine capacity, which makes it easy to scale up or down for a small drip brewer or a large reservoir. It's listed as compatible with drip machines, pod brewers, espresso machines, superautomatics, and kettles, and it's described as odorless and biodegradable.

Good fit if: you own more than one machine (say, a drip brewer and a kettle) and want one product that you dose yourself.

Not a good fit if: you'd rather not measure. Powder needs to be weighed or scooped and dissolved, so a pre-portioned liquid is simpler.

See the Urnex Dezcal descaler

2. Universal Descaling Solution, 2 Bottle Pack (4 Uses)

Two bottles of universal liquid descaling solution for coffee and espresso machines

A liquid concentrate, two bottles with four uses in total, made in the USA. It's listed as compatible with most single-serve, drip, and espresso machine brands, and the product suggests descaling every 2 to 3 months or when your descale light comes on.

Good fit if: you want something pre-measured that works across machine types without doing math.

Not a good fit if: you have very hard water and descale monthly. Four uses would run out in about four months, so a bulk powder may work out better.

See the universal descaling solution

3. Keurig Compatible Descaling Kit (2 Bottles, 4 Uses Plus 4 Filters)

Keurig compatible descaling kit with two bottles of descaler and four replacement water filters

The same style of liquid descaler, four uses across two bottles, plus four replacement water filter cartridges listed as fitting most Keurig brewers (about 2 x 1.25 x 1.25 in). Since you should swap the filter around the time you descale anyway, having both in one box is practical.

Good fit if: you have a Keurig-style brewer with a filter holder in the reservoir.

Not a good fit if: your pod brewer doesn't take a filter, or you only own a drip machine. The filters would go unused, and the plain two-bottle pack above makes more sense.

See the Keurig compatible descaling kit

FAQ

How often should I descale my coffee maker?

Every 1 to 3 months for most homes. If you brew several pots a day or your kettle gets a white crust quickly, aim for monthly. Your machine's manual may give a specific interval.

Can I use vinegar to descale an espresso machine?

Most espresso machine makers advise against it. It's hard to rinse out fully and some brands say it can affect seals. Use a descaler made for espresso machines or the one your manual recommends.

Is descaling the same as cleaning?

No. Descaling removes mineral buildup inside the water path. Cleaning removes coffee oils and residue from the carafe, basket, and group head. Both are worth doing, on different schedules.

The takeaway

Put a reminder in your phone for every two months, keep one descaler in the cupboard, and rinse more than you think you need to. That's really all there is to it. If your coffee has been tasting a little tired lately, try descaling before you blame the beans.

Back to blog